Why does my sewing machine keep eating my fabric?

1. It tries to eat your fabric. This most often happens when you are sewing knits and or if you start sewing too close to the edge of the fabric. … If you’re still having issues, try placing tissue paper under your fabric – it tears off easily and will help prevent your fabric from getting sucked into the machine.

How do I stop my sewing machine from eating fabric?

Five Tips to Stop Your Sewing Machine Swallowing Fabric

  1. Use a fine needle. Before you begin, check that the needle in your sewing machine is fine enough for the fabric that you’re sewing. …
  2. Cover the hole. …
  3. Don’t start sewing on the raw edge. …
  4. Avoid back tacking at the beginning of the seam. …
  5. Try chain stitching.

Why is my sewing machine pulling my fabric?

Cause. Tension pucker is caused while sewing with too much tension, thereby causing a stretch in the thread. After sewing, the thread relaxes. As it attempts to recover its original length, it gathers up the seam, causing the pucker, which cannot be immediately seen; and may be noticeable at a later stage.

IT IS INTERESTING:  Your question: Does tobacco mosaic virus lack nucleic acid?

Why does my sewing machine keep jamming underneath?

However certain you are that the problem with the machine is most likely due to a huge tangled mess of thread in the bobbin underneath the fabric, the most common reason for the jamming is usually the lack of sufficient tension in the upper thread.

What should tension be set on sewing machine?

As the bobbin thread tension is factory-set and wouldn’t usually be adjusted for normal sewing. So we’ll be talking only about the top thread tension since that’s where you’d usually make the adjustments. The dial settings run from 0 to 9, so 4.5 is generally the ‘default’ position for normal straight-stitch sewing.

How do I stop my sewing machine from bunching?

How to Fix Bobbin Thread Bunching and Other Threading Problems

  1. Thread the Machine Properly. Re-thread the upper part of the sewing machine making sure the thread is passing through every single thread guide on its way to the needle. …
  2. Change the Needle. …
  3. Inspect the Bobbin. …
  4. Clean the Machine.

Why won’t my sewing machine needle go up and down?

A disengaged clutch, broken drive belt or internal drive gear failure can prevent the needle from moving. Engage the hand wheel clutch if you have it disengaged for bobbin winding. If the needle won’t move with the clutch engaged, unplug the sewing machine and check the drive belt.

How do you fix puckered fabric?

Loosen your upper thread tension to get it right. Also check if the thread is too tight while it pass through the needle. You can resolve this problem by gradually loosening the thread tension (and testing it with a scrap piece of cloth) until your stitches appear nice and flat, without further puckering.

IT IS INTERESTING:  Question: How long after surgery can stitches be removed?

What causes bobbin thread to bunch up?

Bobbin Thread Tangling



The bobbin keeps pulling and jamming collecting a lot of thread beneath your fabric. There are several culprits for this ranging from a dull needle, improper threading or tension. The tension in both your upper and bobbin threads need to be even. The bobbin could also be placed incorrectly.

How do you fix bobbin tension?

To tighten your bobbin tension, turn the tiny screw on the bobbin case a smidgen clockwise. To loosen bobbin tension, turn the screw counterclockwise. A quarter turn or less is a good place to start.

Why does my thread keep getting caught in the bobbin?

This can be caused if the top thread tension is too tight, or if the bobbin thread is not in the bobbin case tension. … Make sure the bobbin is correctly seated in the bobbin case (bobbin holder), and check that the upper thread tension is not set too tightly.

Why is the tension on my sewing machine wrong?

If the bobbin case falls a couple of inches, the tension is correct. If the bobbin case falls several inches, the bobbin tension is too loose. If the bobbin doesn’t fall at all, the bobbin tension is too tight. There is a small screw on the side of the bobbin.

What tension should I use for stretchy fabric?

For a stretchy fabric, it would be best if you set the upper tension level between 3-4. This adjustment is also a neutral level of tension setting. Step 5: Now, after you have attached the correct needle, stitch type, and tension setting, it is time to test the final stitch on your fabric.

IT IS INTERESTING:  How much is a commercial embroidery machine?

How do you adjust thick fabric tension?

The thicker the fabric, higher the tension must be to lift the lower thread up to the middle of the layers of fabric. You will usually be alright with a 4 or 5 on medium to medium-heavy fabrics like linen and twill weaves such as drill and denim.

My handmade joys