Your question: Why won’t my sewing machine catch the bobbin thread?

Why won’t my sewing machine catch the bobbin thread?

Why won’t my machine pick up the bobbin thread? … Also, make sure your bobbin is in correctly (not backwards) and that the upper tension disks of your machine are threaded correctly. Make sure the presser foot is up when seating the thread through the upper tension. Now, it’s time to draw up your bobbin thread.

Why is my bobbin winder not working?

The two most common problems are that you either need a new bobbin tire, or just need to adjust the position of the winder a little closer to the hand wheel. Remove the top cover and you will see the winder assembly. Loosen the two screws that hold the assembly nudge it closer to the hand wheel side.

Why won’t my sewing machine needle go up and down?

A disengaged clutch, broken drive belt or internal drive gear failure can prevent the needle from moving. Engage the hand wheel clutch if you have it disengaged for bobbin winding. If the needle won’t move with the clutch engaged, unplug the sewing machine and check the drive belt.

IT IS INTERESTING:  How do you make easy tab top curtains?

What tension should my sewing machine be on?

The dial settings run from 0 to 9, so 4.5 is generally the ‘default’ position for normal straight-stitch sewing. This should be suitable for most fabrics. If you are doing a zig-zag stitch, or another stitch that has width, then you may find that the bobbin thread is pulled through to the top.

Why does my thread bunch up underneath?

Your Thread Tension Is Too Tight



Sewing machine manufacturers suggest that you don’t mess with your bobbin thread tension too much, but you should adjust your upper thread tension if you keep getting bunched up thread underneath your fabric. If your tension is too tight, it can pull your thread and break it.

What is bobbin fill thread?

Quite simply, it’s a lightweight thread that you wind on to your bobbin. … You use this thread when using an embroidery thread for embroidery or decorative stitches.

Can I sew without a bobbin?

You can’t sew without a bobbin, as the machine requires two spools in order to operate properly. Therefore, you will need to add the bobbin thread in addition to your needle thread.

What is the difference between bobbin thread and embroidery thread?

Machine embroidery bobbin thread is different from regular thread. … Typically, it is either 60 or 90 weight, whereas standard embroidery thread is typically 40 weight. And, a higher weight number means a thinner thread. Another difference is that machine embroidery bobbin thread typically only comes in white.

How do you fix common sewing machine problems?

HERE are 10 most common trouble areas of a sewing machine:

  1. Change the Needle. …
  2. Clean the Machine. …
  3. Check the Top Threading. …
  4. Quality Thread. …
  5. Bobbin thread not in the bobbin tension. …
  6. Not having your machine cleaned annually. …
  7. Wrong bobbin. …
  8. Needle not high enough.
IT IS INTERESTING:  Your question: Can Muslims wear waist beads?

Why does my sewing machine keep stopping?

Often, your sewing machine will suddenly stop working due to a bent or broken needle which stops the thread from going through the fabric. The solution: Stop work and carefully inspect your needle for any deformities or breakage, and if you see any – replace it with a new one.

What causes a sewing machine to lock up?

Sewing Machine: Machine locks up. Thread bunched up in the shuttle race often causes the sewing machine to lock up. … Clean lint and debris out of the shuttle race; they can prevent the needle from hooking the thread, resulting in thread bunching up in the shuttle race and jamming the needle.

Why won’t my sewing machine feed the fabric through?

If Fabric Is Not Feeding Properly



Lower the presser foot and resume sewing. Another reason the machine may not be feeding fabric is that the feed dogs (or feed teeth) are disengaged, so make sure that they are properly engaged for sewing. … The machine may also not feed fabric if the stitch length control is set to “0”.

My handmade joys